×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial Manager50W monocrystalline silicon solar module performance is tested with experimental measurements conducted at Baghdad city /Al-Jaderia (33.26 N, 44.21E). Solar irradiance striking is subjected to more losses which after the experiments conducted resulted approximately in 15% of the total energy which is converted into electric power energy. To study the effect of temperature variations on solar performance, solar irradiance must be kept constant and vice versa. Therefore, to have of the temperature range and for more accuracy, the measurements was done for tested module with three solar radiations levels; 500, 750 and 1000 W/m2. The maximum value of power (Pmax) at solar radiation intensity 1000W/m² was 46.34 W on January 2025 at cell temperature 24.1 oC, with the corresponding the maximum open voltage, and open circuit current 18.28 V, and 2.944 A respectively. The highest value of efficiency was 13.5 % January 2025 at solar radiation 500W/m². Consequently, The minimum value of power (Pmax) at solar radiation intensity 500W/m² was 27.54 W on October 2024 at cell temperature 40.5 oC, with the corresponding the maximum open voltage, and open circuit current 18.01 V, and 1.752 A respectively. The lowest value of efficiency was 6.9 % October 2024 at solar radiation 1000W/m². In general, the results showed slightly decrease in short circuit current with temperature increasing. With temperatures change great influence on the output voltage especially on open circuit voltage while very small decrease in the output current has been noticed.
In this research paper, it has been studied the influence of the temperature of the cell on the performance and behavior of two types of modules, which are mono-crystalline silicon (mc-Si) and poly-crystalline silicon (pc-Si) solar modules. The experimental work has been achieved under the outdoor conditions, where the range of cell temperature is between 20 and 60 °C. It was applied three different values of solar radiation [500, 750, and 1000W/m2 (standard condition, where cell temperature of 25 °C, solar irradiance of 1000 W/m², and air mass AM 1.5)]. All tests are achieved under the Iraqi weather conditions in the city of Baghdad city. It was computed the temperature coefficients for each module and during any time during the experiment. It was found that the open circuit voltage decreased with -0.0912 V/ºC and -0.07 V/ºC when using the pc-Si module and mc-Si, respectively. While, the short circuit current increased slightly with 4.4 mA/ºC and 0.3 mA/ºC corresponding to the pc-Si and mc-Si, respectively. Finally, the lowest drop in output power was found when using the pc-Si module (-0.0915 W/ ºC), and the highest drop when using the mc-Si module (-0.1353 W/ ºC).
The conventional open sun drying is not efficient, it is slow and contaminated and there is a necessity to develop highly advanced technologies in solar drying. The review looks critically at solar dryers that are improved with concentrator, optical, thermal energy storage (TES) or phase-change materials (PCM). The incorporation of parabolic trough or compound parabolic concentrators leads to a high temperature of over 100-115 oC and a thermal efficiency of up to 88 %. Reflective walls are also made to enhance optical capturing by up to 37.6 %, and shorten drying time by 15-20 %. TES/PCM systems increase the operation of TES systems beyond the sunset, nano-enhanced PCMs reduce drying time by 40% and enhance thermal efficiency by more than 48%. These systems demonstrate short payback periods (0.43-5.14 years) with regard to economics. They minimise the emission of CO2 by 2-44 tons/ lifetime of systems. These combined technologies have addressed intermittency and low efficiency and enabled solar drying to be a reliable and cost-effective and sustainable solution, as the UN Sustainable Development Goals of clean energy and climate action suggest.
The objective of the current study is to determine the accuracy of a computational model that has been developed to simulate polyurethane foaming reactions by comparing its results with experimental findings on the system using both physical and chemical blowing agents. There was high concordance between the model outputs and the laboratory results in regard to the temporal development of reaction temperature as well as the resulting foam density, both of which were highly faithful recreations. The discussion provided further information about the optimization of the performance of cyclohexane, particularly when used in synergy with chemically active blowing agents, which speed up foaming. Besides, the polymerization dynamics were contained in the simulation, thus providing rich information on the structural changes that occur during the foaming process. Taken together, the results present a strong basis for the process performance optimization, as well as the predictive modeling of the blowing agent behavior. In the future, it will involve expanding the simulation model to include a wider range of agents, reaction mechanisms, and kinetics.
Nanoparticle additives emerge as a modern solution to eliminate the performance gap between conventional water-based drilling fluids (WBDFs), and more superior but environmentally challenging oil-based drilling fluids (OBDFs). This study focuses on the enhancement of KCl polymer mud using nano-additives. While nano-additives like copper oxide (CuO NPs) were studied and showed promising results, another form of copper (elemental copper nanoparticles, Cu NPs) with a potential as a multifunction mud additive remains largely unexplored. This research systematically investigates the impact of Cu NPs (0.04–0.8 wt%) on the lubricity, rheology, and filtration properties of KCl polymer mud. All the measurements were done in the lab at room temperature, using lubricity tester, viscometer, and low-pressure filter press. Most additives tend to enhance one property of the mud, but the Cu NPs acted as a more superior properties enhancer, as it didn't enhance only one aspect of KCL polymer mud, but acted as multifunctional additive. For the lubricity, the effect of Cu NPs was significant on the coefficient of friction (CoF), with maximum reduction of 41.68% observed at 0.8% concentration, however at the 0.2% concentration, a relatively similar result of CoF reduction was observed with 39.78% making it the optimal concentration for the lubricity aspect. For the rheological properties, the addition of Cu NPs to the KCL polymer mud enhanced the overall rheological properties, increasing the plastic viscosity (PV), yield point (YP), apparent viscosity (AV), and gel strength, the highest values [PV (44.5 cP), YP (69.4 lb/100ft²), AV (77.35 cP)] were observed at 0.2% concentration. Unlike its beneficial effects on lubricity and rheology, the addition of Cu NPs to KCl polymer mud resulted in increased fluid loss and thicker filter cakes. The study concludes that a concentration of 0.2 %wt of Cu NPs is optimal for the simultaneous enhancement of lubricating and rheological properties in KCl polymer mud. This study highlights the potential of Cu NPs as a multifunctional additive that can be used in advanced water–based drilling fluids systems.